In the daily use of the sprayer, the sprayer will always suffer from poor spray effect, leaking or unscrewing of the switch, and leakage of water at the connection site. How to eliminate these faults?
Inadequate spray pressure leads to poor atomization. If the rocker is toggled more than 15 times during spraying, the pressure in the barrel has not reached the working pressure. The vegetable farmer should first check whether the water inlet ball valve is thrown away by debris, resulting in insufficient air pressure and affecting the fog. Effect. The inlet valve can be removed, if there is, then use a rag to clean; if the spray pressure is still insufficient, you should check whether the air chamber damage inside the leather cup, if damaged, you need to replace the new skin; if sealed due to the connection site If the air leakage is caused by the unmounted or broken rings, seals should be added or replaced.
The spray nozzle of the spray nozzle body is blocked by the dirt. It is one of the most common factors causing the spray to not fog. The vegetable grower can remove the spray nozzle and blow the air from the spray hole in reverse direction to remove the jammed dirt. If the nozzle is blocked, the cleaning nozzle hole can be dismantled. However, it is not allowed to use hard materials such as iron wire to prevent the nozzle hole from expanding and affect the quality of the spray. If the screen is blocked by the filter or the ball of the overflow valve is contaminated, The filter should be cleaned and the dirt that has left the ball should be cleaned.
If the switch is not tightened, the switch cap should be tightened. If the switch is worn due to the washer on the switch core, the gasket should be replaced. The switch does not move much because it is placed for a long time, the switch core is etched by the medicament and sticks. The vegetable grower should put the switch in kerosene or diesel oil for a period of time, and then remove and clean it.
If water leaks at the joint, loosen the joint, tighten the nut. If the gasket is not flat or damaged, place the gasket flat or replace the gasket.
Inadequate spray pressure leads to poor atomization. If the rocker is toggled more than 15 times during spraying, the pressure in the barrel has not reached the working pressure. The vegetable farmer should first check whether the water inlet ball valve is thrown away by debris, resulting in insufficient air pressure and affecting the fog. Effect. The inlet valve can be removed, if there is, then use a rag to clean; if the spray pressure is still insufficient, you should check whether the air chamber damage inside the leather cup, if damaged, you need to replace the new skin; if sealed due to the connection site If the air leakage is caused by the unmounted or broken rings, seals should be added or replaced.
The spray nozzle of the spray nozzle body is blocked by the dirt. It is one of the most common factors causing the spray to not fog. The vegetable grower can remove the spray nozzle and blow the air from the spray hole in reverse direction to remove the jammed dirt. If the nozzle is blocked, the cleaning nozzle hole can be dismantled. However, it is not allowed to use hard materials such as iron wire to prevent the nozzle hole from expanding and affect the quality of the spray. If the screen is blocked by the filter or the ball of the overflow valve is contaminated, The filter should be cleaned and the dirt that has left the ball should be cleaned.
If the switch is not tightened, the switch cap should be tightened. If the switch is worn due to the washer on the switch core, the gasket should be replaced. The switch does not move much because it is placed for a long time, the switch core is etched by the medicament and sticks. The vegetable grower should put the switch in kerosene or diesel oil for a period of time, and then remove and clean it.
If water leaks at the joint, loosen the joint, tighten the nut. If the gasket is not flat or damaged, place the gasket flat or replace the gasket.
Greenhouse Film Electric Roll Up
The Greenhouse Film Manual Roll Up Unit can roll up a length of 60-80 meter, running stably with fine out side looking and long time of usage. The inside drive gears are made of high quality steel with fine workmanship, and what is more, there is lubricating bearing assembled on the out put and input shaft. At the meantime, there is also a group of reverse gear added to it. All these make the unit to be light and easy for
Greenhouse Film Electric Roll Up,Roll Up Curtain Greenhouse,Greenhouse Film Vent Roller,Greenhouse Roll Up Motor
JIANGSU SKYPLAN GREENHOUSE TECHNOLOGY CO.,LTD , https://www.thgreenhouse.com